How to Install a Whirlpool Bathtub . Position the template over the existing hole and tape into place. Cut the paper template along the cutting line, then use a marker to trace the cut line onto the tape. If a professional is cutting the surround, he or she should handle this step.

How To Tile A Shower. In this third and final article of the How To Build a Shower Series, we discuss finishing your shower with tile. In the first two articles of our Building a Shower Series, we walked through the framing, plumbing and shower pan construction of building a walk in shower. In this third and final article, we document the final steps to completing your shower — preparing for and installing shower tile. Prior to starting this final step of your shower construction project, you should have completed the framing, plumbing, and shower pan construction steps (Articles 1 and 2 above).

Prior to starting the tiling process, all supply and drain plumbing should be installed, tested and ready to go. Your mixing valve(s) should be in place and calibrated as needed. The supply lines to future shower heads should be installed, properly supported and terminate with a securely mounted drop ear elbow or suitable fitting that is stubbed out and capped.

The shower pan should be complete, with a properly installed shower drain. Tile installations require a fairly flat, stable surface that is appropriate for the adhesive thin- set mortar used to install tile.

The FloorElf describes the technique for installing tile on a shower ceiling without it dropping on your head. You laugh now! It’s all fun and games until you get. Install crossbraces so you can anchor the pipes firmly. Cut pieces of 2x4 or 1x4 to fit snugly between studs and attach them by drilling pilot holes and driving screws.

Give your old, worn out vinyl floor a new look with elegant tile. We'll show you how to save hundreds of dollars by installing the floor yourself. To reduce hassles later, check the dimensions of the new tub surround (including the nailing flanges) before you cut out the old surround or tile wall. DIY How To Bathroom Remodeling Tips Guide Help Do It Yourself Techniques for Bathroom Renovations Pictures Photos. Give your shower or tub a makeover with tile. Tiling a Shower Enclosure or Tub Surround. Give your shower or tub a makeover with tile. Here's a recap of how we installed subway tile in our shower and marble on our floors. Remove the faucet and handles and set them aside. Use a utility knife to cut away the silicone seal around the tub. Lift the tub out of the surround and remove it.

For wet environments (like a shower), tile backing surfaces must be appropriately water resistant. In general this means installing cement based or similar tile backer board. Years ago, water- resistant gypsum wallboard (“green board”) was used as a low- cost wall sheathing and tile backer in wet areas like showers.

This product, a wax coated gypsum wall board, routinely failed in wet environments. Building codes now prohibit the use of these products as the tile backer in showers. Do not use Greenboard as a tile backer in showers! Today, there are many tile backer boards designed for bath and shower use. In general, there are four main types of backer board that can be used for shower construction.

They are: For my shower project, I used Hardie. Backer fiber cement backer board. I chose this product over fiberglass reinforced cement board (Durock or similar) for its performance in wet areas and smooth surface. Not only did I plan to install tile backer board for the shower, but the entire bathroom. Hardie. Backer’s smooth surface made the non- tile areas easy to paint. As further waterproofing for the bath and shower, I added a paint- on moisture barrier. I applied this barrier over the Hardi.

Backer in the shower and behind the sink and toilet in the bathroom. Although wet- area approved tile backer boards are quite water resistant, many do not stop the movement of water. Vapor barrier requirements depend on local codes and specific applications (Steam Shower use, etc.). Most installations in showers should have either a vapor barrier behind the backer board (poly sheeting) or one on top of the backer board (paint- on membranes) applied before tiling.

I prefer paint- on barriers. I like the idea of blocking water before it passes through the cement board. Also, consider that any vapor barrier behind the cement board will have fastener penetrations compared to the continuous, uninterrupted barrier that a paint- on product provides. Two commonly available paint- on membranes are; Redgard (Custom Building Products, Home Depot), Hydro. Barrier, and Hydro Ban (Laticrete). I used Hydro Barrier by Laticrete (highly recommended).

How To Install Drywall Around A Tub Before Tiling A Bathroom

Shop Weed Warrior® Universal Push-N-Load 3 Blade Head (14867).

Both products allow thin- set tile adhesives to be applied directly to the membrane once it has dried. Once you have installed, taped and waterproofed your tile backer, its’ time to install your tile.

Tiles are thin flat pieces of clay, stone, or other material used as a construction surface finish. Tile is often used to finish floors, walls, showers, pools, patios, and counter- tops. Tile finishes are very durable and perform well in wet environments. Tiles are installed side- by- side using mortar based adhesives called thin set. The gaps between the tiles are then filled with grout; a durable filler often mortar- based with or without sand. Tile a Shower – Step by Step.

Install tile backer board. Select a tile backer board approved for shower use.

Install the backer board with backer board screws or roofing nails (both approved by The Tile Council of North America). Most panels can be installed horizontally or vertically – check the installation instructions for your product. Hardie. Backer 1/2. We fastened the backer board using Buildex Backer- On screws. We found it a bit difficult to get these screws flush with the Hardi. Backer board. Roofing nails may be a better match with Hardie.

Backer as the heads are thin and very easy to nail flush. Cutting Backer Board Can Be Dangerous – Follow Manufacturers Recommendations. Portland cement based backer boards contain silica sand.

Cutting these products can create dangerous silica dust. When cutting any cement board product, use great care to avoid silica dust formation and exposure.

Exposure to silica dust is linked to lung cancer and the lung disease silicosis. Use manufacturer approved cutting methods (shears, score and snap) and clean up (HEPA filter vacuums or wet clean up, avoid sweeping or methods that create dust). Most panels can be cut by scoring and snapping similar to dry wall. Specially designed carbide tipped scoring tools are available for this purpose. Cutting shower backer board using specialized carbide tip tool to score and snap panel.

Refer to recommendations from the product manufacturer for specific guidelines on cutting the product you are using. Always wear a particle mask or respirator when working with these products. Avoid using of high- speed power tools (grinders, circular saws) unless they are have attached dust evacuation systems.

When mounting the backer board, horizontal blocking is not necessary for most boards but does add stability (we added horizontal blocking, where it was simple to do). Reference the installation instructions for the product you plan to use for specifics on panel direction and framing requirements. As with all sheathing, be sure to gap panel edges by 1/8. If you plan to sheath your ceiling with backer board, use long fasteners — 1 1/2. Smooth seams and tape with additional thin- set. See #6 below for more information on mixing thin- set mortar.

Shower backer board installed. Seams filled with latex modified thin- set and reinforced with alkali- resistant fiberglass tape. Apply paint- on waterproof membrane (optional, but recommended). Waterproof your shower by applying a paint- on surface water barrier. Shower approved tile backer boards are tolerant of water, but they do not stop it. Protect your framing and wall cavities by applying a vapor barrier. Hydro Ban paint- on waterproof membrane applied to shower walls and ceiling.

Although it is acceptable to use plastic sheeting installed behind tile backer board as a vapor barrier, it is not the best practice. Using paint- on waterproofing barriers block water at the surface of the backer board. Why not deny water passage into your wall, instead of trapping it behind the backer board with plastic sheeting? There is a variety of paint- on products available. I used Hydro. Ban from Laticrete. This paint- on product is easy to apply and does not require fabric reinforcement at the corners and seams (some products do). Although no fabric reinforcement is necessary, corners, penetrations, floor- wall transitions and other critical areas should be pre- treated with a liberal application of the product prior to applying two field coats.

Allow the product to cure before setting tile (2 hours for Hydro Ban). Most paint- on membranes allow the use of thin- set adhesives directly over the paint- on membrane once cured. Plan tile install. Plan the layout of your shower tile. Start with a level baseline just above the shower pan. Mark significant structures (the window in our case) with a horizontal reference around the shower to help plan tile seems. Plan out tile install. Hack Facebook With Phone Number.

Start with level reference. Mark the walls with horizontal and vertical reference lines prior to setting tile.